Sent Datasheet sending
Sending the product data sheet to your e-mail address.
Inquiry sent Information
Request information about the product to your e-mail address.
Security systems / Systems with keypads / Micron control panels BackMICRON SCORPION Z4120C panel4+1 zone alarm center panel with communicator.
- Optionally programmable zones: Z4120C 4 pieces + 1 piece 24-hour zone.
- Built-in communicator. - A separate reporting code can be assigned to each event and each zone. - You can signal to several remote monitors one after the other, or even to your own phone number with a signal that can be interpreted. - In the event of an alarm, an alarm tone can be transmitted to phone numbers that can also be set by the user. - Alarm signal for your own telephone devices: siren sound and the number of beeps corresponding to the zone that triggered the alarm. - Connectable LED operator, LCD operator, Night armer, remote control, key switch, or even a combination. - 4 operators plus 1 remote control module can be connected at the same time. - All functions can be remotely controlled using a remote control. - All keyboard commands can be programmed to remote control transmitter buttons, so the remote control can be set as desired. - NiteWatch for bedroom, night arming, night mode disarming and system status indication. - Programming can be done with an LED or LCD operator or from a PC using the MicroCom upload and download software. - Memory Chip can be connected to upload and download complete programs (cloning). - 10 different freely programmable zone types. - Immediate, 24-hour, night, entry-delayed, alternative, follow-up, intelligent, automatically opt-out... - Separately programmable exit delays, entry delays, alternative entry delays. - Reaction times can be changed per zone. - Subsequent zones: if the first violated zone is delayed, these zones will also be delayed. - Automatic zone exclusion: The zone can be excluded after a specified number of detections in an alarm cycle. - Intelligent zone mode: only two detections trigger an alarm, which occurs in the same and/or different zones. - Entry alarm mode: the operator gives 3 short beeps when the designated zones are detected in the disarmed state. - 24 user codes, which can be created and changed by the user if allowed by the installer. - Programmable code properties (e.g. the code can only arm, disarm, can also be used via telephone...). - Master codes for user settings and a separate programmer code. - The user can also create temporary codes, which are automatically deleted at midnight on the day of their creation. - Quick focus. - Night (stay at home) arming, for arming only specific zones, with separate key commands. - Arming with exit and/or entry delays. - Warning sounds during the delay times, which can be switched on and off per zone. - Arming by bypassing zones. - Automatic arming at the time set by the user or programmed by the installer, even every day. - The ’Pre-alarm sound’ indicating automatic arming can be programmed for 0-9 minutes (the operator sounds every 6 seconds). - Night lock: when arming with a certain code, the other codes become ineffective. - Panic alarm, fire alarm, call for help, forced deactivation signal. - Force disarm indication. - Arming and disarming via telephone line with status indication tones. - Programmable LCD operating function keys. - Telephone line input and separate telephone output for other equipment using the telephone line. - Receiving an incoming call from the operator manually or automatically after a set number of rings. - Bypass answering machine (double call) function to access the panel if other devices can receive the call. - Automatic disconnection from other devices when sending a report or alarm signal. - Event memory for the last 128 alarm events. - Querying system states and errors. - Resetting the smoke detector with a separate keyboard shortcut. - Zone closing resistors EOL. - Sensors with normally closed (NC) or open (NO) contacts can be connected at the same time. - Uninterrupted power supply by connecting a battery. - Adjustable battery charging voltage. - The system constantly monitors and tests the connected devices. - Phone line monitor, siren output monitor, AC power and battery monitor, power output monitor. - User communicator test and automatic communicator test can be programmed per day and time. - 4 different phone line monitoring modes. - 1500 mA siren output, to which almost any buzzer can be connected. - 500 mA power outputs. - 2 programmable (PGM) outputs that can be controlled by almost any event. - 250 mA OUT 1 and 50 mA OUT 2 programmable outputs. - The state of the outputs can also be programmed so that they have voltage at rest or when activated. - Programmable timings: how long siren output and programmable outputs should be activated separately. Most often purchased with the product:DSC LCD PK5501SATEL CA4VKLEDPARADOX K10VPARADOX Digiplex K641BL+MICRON RCM-1Bosch RF3501LEDSC RF5132-433PARADOX DCT10-868Security systems / Systems with keypads / Micron control panelsBack New page × | ||||||||||||||||||||||||||||||||||||||||||||||||||
Copyright © 2024 securityeurope.eu © | DELTON | All rights reserved.
|
Our website uses cookies to make it easier to use, to which you contribute by further browsing. Information | × |